
Telehandler Camera System Fitment Guide
Find your telehandler, match the size class, and order the right RioV360 kit.
This guide groups telehandlers by rated capacity, from compact 5,500 lb machines to 12,000 lb high-capacity and rotating models, with the RioV360 kit, power connection, accessories and camera layout for each class. Find your JLG, SkyTrak, Genie, Cat, JCB, Skyjack, Bobcat or Manitou model and order with confidence.
How to Use This Telehandler Camera Fitment Guide
- Find your brand and model in the table below. Most model numbers give the rated capacity and lift height.
- Match the size class to its power connection and accessories. Most telehandlers run 12 V, and RioV360 connects directly.
- Confirm the model and voltage on the machine data plate. Model ranges change by year and region.
- Plan the layout on the chassis: rear counterweight, right side, left side and front, plus the monitor in the cab.
- Order the complete kit plus any accessories listed for your class.
Take it to the shop floor. The printable fitment guide has the size class and brand tables, power connections, camera and beacon layout, accessories and PILOT unit details in a PDF.
Telehandler Camera System Fitment by Size Class
| Size class | Rated capacity | Power | RioV360 power connection | RioV360 Accessories | Notes |
|---|---|---|---|---|---|
| Compact | About 5,500 to 6,000 lb, under 25 ft | 12 V | Direct: 12 V key-switched circuit | RV360-EXT, RV360-512, RV360-MAG | Farms, landscaping and tight sites. Short frame, standard cables reach. |
| Standard | About 6,000 to 9,000 lb, 36 to 44 ft | 12 V | Direct: 12 V key-switched circuit | RV360-EXT, RV360-512, RV360-CBX | The rental workhorse. Boom and engine block the operator's right side. |
| High-Capacity | About 10,000 to 16,000 lb, 42 to 56 ft | 12 V on most | Direct: 12 V or 24 V key-switched circuit | RV360-EXT, RV360-CBX, RV360-512 | Long frame: CBX cables reach the rear counterweight and front frame. |
| Rotating / Heavy-Load | Rotating upper, or over 16,000 lb | 12 V or 24 V | Direct: 12 V or 24 V key-switched circuit | RV360-EXT, RV360-CBX, RV360-512 | Rotating: mount on the upper so cameras turn with the cab. Check voltage on the data plate. |
| Battery Electric | Compact and rotating | Low-voltage accessory circuit | Key-switched 12 V accessory circuit, or RV360-DCC | RV360-EXT, RV360-512, RV360-DCC if needed | Manitou MT 625e, MRT 2260e and similar. Never connect to the drive battery. |
Telehandler Models by Brand and Size Class
| Brand | Compact | Standard | High-Capacity | Rotating / Heavy-Load |
|---|---|---|---|---|
| JLG / SkyTrak | Not listed | SkyTrak 6034, 6042, 8042 | SkyTrak 10042, 10054, 12054; JLG 1055, 1255, 1644 | Not listed |
| Genie | GTH-5519 | GTH-636, GTH-844 | GTH-1056, GTH-1256, GTH-1544 | Not listed |
| Cat | TH255C | TH0642, TH0842 | TH1055, TH1255 | Not listed |
| JCB | 505-20 | 506-36, 507-42, 509-42, 510-42 | 510-56, 512-56, 514-56 | Not listed |
| Skyjack | SJ519 TH | SJ643 TH, SJ843 TH | SJ1044 TH, SJ1056 TH, SJ1256 THS | Not listed |
| Bobcat | TL519, TL623 | TL723, TL923 | Not listed | Not listed |
| Manitou | MT 625, MT 625e | MT 735, MT 935, MT 1135, MT 1335 | Not listed | MRT 2260, MRT 2660, MRT 3060; MHT 790 to MHT 11250 |
Older Telehandlers
| Brand | Older series | How to match |
|---|---|---|
| JLG / SkyTrak | G-series (G6-42A, G9-43A, G10-55A, G12-55A), SkyTrak 6036 and earlier | A G10-55A fits like the 1055 |
| Genie | GTH-842, GTH-1048 and earlier GTH models | A GTH-842 fits like the GTH-844 |
| Cat | TL642, TL943, TL1055, TL1255 (C and D) | A TL943D fits like the TH0842 |
| JCB | 506C, 506CHL, 508C and earlier Loadalls | A 508C fits like the 509-42 |
| Skyjack | VR series (VR1056 and similar) | A VR1056 fits like the SJ1056 TH |
| Bobcat | V-series VersaHANDLER, TL619 | Match by rated capacity |
Older telehandlers fit by rated capacity. Most model numbers give the capacity and lift height, so an older machine fits like the current model with the same capacity. Not listed? Send the make and model and we will confirm the kit within one business day.
Size classes, capacities and model lists are approximate and vary by year, region and configuration. Brand and model names are trademarks of their owners. RioDatos is not affiliated with or endorsed by any manufacturer listed. Model names are used only to identify compatible machines.
Telehandler Camera System Power: 12 V, 24 V and Electric
- Compact, standard and most high-capacity telehandlers: 12 V system. Connect to a fused, key-switched 12 V circuit and the constant 12 V line, as the user manual shows.
- Heavy-load and some rotating telehandlers: may run 24 V. RioV360 connects directly to either, with no converter. Check the battery or data plate.
- Battery-electric telehandlers: connect to the key-switched 12 V accessory circuit. If there is none, add the RV360-DCC isolated DC-DC converter. Never connect to the drive battery.
RioV360 User Manual: installation, settings and troubleshooting. Download the RioV360 User Manual (PDF, v4.4).

Camera / Beacon Layout for Telehandlers
- Rear: on top of the rear counterweight, aimed down at the reverse path.
- Right side: on the right rear fender or engine cover, aimed forward. The boom and side engine block the operator's right view.
- Left side: on the left rear corner behind the cab, aimed forward along the cab door and front tire.
- Front: low on the front frame or cab roof front edge, aimed at the travel path. A raised or carried load blocks the forward view.
- Monitor: on the right front cab post with the RV360-EXT kit, clear of the load view and joystick reach.
- Beacon: on the counterweight or cab roof rear, where ground crews can see and hear it.
Mount on the chassis, never on the boom, so the view does not move as the boom extends. On rotating telehandlers, mount on the upper structure so the cameras turn with the operator.
No tags for workers to wear: the AI cameras detect any person in the zone.
RioV360 Accessories in This Guide
- RV360-EXT: Monitor Extension and Mounting Kit: rail clamp, round base, cab-frame bracket or T-attachment.
- RV360-CBX: Extension Cables: two 3 m and two 5 m camera cables plus a 5 m monitor cable for long frames.
- RV360-512: Upgraded Storage: 512GB card for about 60 hours of continuous video.
- RV360-MAG: Magnetic Camera Mounts: no-drill mounting on the steel cab and fenders, ideal for trial positions and rental machines (US shipments).
- RV360-DCC: Isolated DC-DC Converter: for battery-electric telehandlers with no low-voltage circuit. Priced on quote.
PILOT Unit Program
Prove It on Your Telehandler Before You Commit
Put RioV360 on the telehandler with the most people around it and let your operators, foremen and EHS team see it work on your own site. No long trial agreements and no software to set up. Install it, run it, and decide.
- Pick the telehandlerChoose the machine with the most people working around it.
- OrderSend the make, model and serial number. Pay by credit card.
- Ships fastIn-stock units ship from Arizona in 2 business days.
- InstallFollow the user manual and the layout in this guide.
- Roll outUse the same kit and layout across the rest of the fleet.
Included with the PILOT unit: 4 AI cameras, 7 inch monitor, 120 dB voice beacon, 256GB card, wiring harness, mounting hardware, user manual and 18-month warranty. Phone, email or Teams support for your installer.
Recommended PILOT Unit Accessories
Upgraded Storage
512GB high endurance card for about 60 hours of continuous video.
Monitor Extension and Mounting Kit
Rail clamp, round base, cab-frame bracket or T-attachment.
Magnetic Camera Mounting Kit
No-drill camera mounts to trial positions on the cab and fenders.
Extension Cables
Camera and monitor extensions for standard and larger telehandlers.
Frequently Asked Questions
Does RioV360 fit JLG and Genie telehandlers?
Yes. JLG, SkyTrak and Genie telehandlers run a 12 V system and RioV360 runs on 8 to 32 V, so it connects directly.
Where do the cameras go on a telehandler?
On the chassis: rear counterweight, right fender or engine cover, left rear corner and front frame. Never on the boom, so the view stays steady.
Can RioV360 move between rental telehandlers?
Yes. With RV360-MAG magnetic mounts the cameras need no drilling, so a unit can move to another machine of the same class.
Do workers need to wear tags?
No. RioV360 uses AI cameras to detect any person in the zone, with nothing to wear or charge.
More for these sites: telehandler pedestrian detection and construction pedestrian detection.
Request a Telehandler Camera System Quote
Send your telehandler makes, models and quantities. Within one business day, we will email pricing, the recommended kit and accessories.
Prefer to talk? Call John directly at +1 (520) 501-0602 or email info@riodatos.com.
